CAN I SET UP A TUB MYSELF?

Can I Set Up A Tub Myself?

Can I Set Up A Tub Myself?

Blog Article

Get Quote

Just how do you feel when it comes to Tools You Need to Install a New Bathtub ?


Tools You Need to Install a New Bathtub
Setting up a bathtub isn't specifically brain surgery, but it does call for strong plumbing, carpentry, and also often, tiling skills. Changing an old tub with a new one is additionally a moderately hard job. If the old tub is conveniently available, the project can relocate quickly; if you need to open a wall surface to eliminate the old tub and also position the brand-new bathtub, the job is much harder. In either instance, the job is within a home handyman's abilities, although you will require a helper to leave the old tub and also set in the brand-new one. Make sure you have actually qualified on your own for the job and also are comfortable trying it. Rather than working with a professional to take control of a halfway-completed project, it is far better to consider utilizing one before you start. Possibilities are you might need a specialist plumber to make tube connections.
This post will assist you mount a new tub in your bathroom if you have currently acquired a new bathtub and also don't need to alter the setup of your previous supply of water pipelines.
Your tools as well as product checklist ought to consist of the following:
  • New Bathtub

  • Hammer

  • Pipe Wrenches

  • Prybar

  • Shatterproof glass

  • Level

  • Pliers

  • Adjustable Wrench

  • Putty Blade

  • Screwdriver

  • Cold Chisel

  • Tape Measure

  • Pipeline Caps


  • Removing Old Touches


    If you need to replace old faucets with brand-new ones as a part of your installation, after that the first thing you need to do is disconnect the water system. After doing so, activate the taps to drain any type of water continuing to be in the system. The process of removing the existing faucets can be fairly problematic due to the restricted gain access to that is usually the case.
    Use a basin wrench (crowsfoot spanner) or a faucet device to reverse the nut that connects the supply pipes to the faucets. Have a cloth prepared for the staying water that will certainly originate from the pipelines. Once the supply pipes have been eliminated, utilize the very same device to loosen up the nut that holds the taps onto the bath/basin. You will need to stop the single faucets from transforming throughout this procedure. As soon as the taps have been removed, the holes in the bath/basin will have to be cleaned up of any type of old securing substance.
    Prior to going on to fit the brand-new faucets, contrast the pipe connections on the old taps to the new taps. If the old taps are longer than the new taps, then a shank adapter is required for the new taps to fit.

    Fitting New Taps


    If the tails of the new taps are plastic, then you will need a plastic connector to prevent damage to the thread. One end of the connector fits on the plastic tail of the tap and the other end provides a link to the current supply pipelines.
    If you require to fit a monobloc, after that you will need decreasing couplers, which links the 10mm pipe of the monobloc to the basic 15mm supply pipe.
    Next, position the faucet in the placing opening in the bath/basin making sure that the washing machines remain in location between the tap and the sink. Safeguard the faucet in position with the maker offered backnut. When the tap is securely in position, the supply pipes can be connected to the tails of the taps. The faucets can either be attached by utilizing corrugated copper piping or with typical tap connectors. The previous kind ought to be connected to the tap finishes initially, tightening only by hand. The supply pipelines can later on be linked to the other end. Tighten both ends with a spanner after both ends have actually been linked.

    Setting up the Bathtub


    Using both wooden boards under its feet, place the bath tub in the called for setting. The wooden boards are helpful in equally spreading out the weight of the bathtub over the location of the boards as opposed to focusing all the weight onto four tiny points.
    The next objective is to make sure that the bathtub is leveled all round. This can be attained by examining the spirit level and readjusting the feet on the tub until the level checks out level.
    To set up taps, fit all-time low of the outermost flexible faucet port to the appropriate supply pipeline by making a compression join; after that do the exact same for the other faucet.
    Switch on the water as well as check all joints and also new pipework for leakages as well as tighten them if necessary. Fill up the bathtub as well as also examine the overflow outlet and also the typical outlet for leakages.
    Ultimately, repair the bathroom paneling as described in the maker's instruction manual. Tiling as well as sealing around the tub should wait up until the bathtub has actually been used a minimum of when as this will resolve it into its last position.

    Preparing for the Setup


    To start with, the supporting structure supplied with the bathroom should be fitted (if needed) according to the supplier's directions. Next off, fit the taps or mixer to the tub. When suitable the tap block, it is necessary to make sure that if the tap features a plastic washer, it is fitted between the bath and also the faucets. On a plastic bath, it is also sensible to fit a supporting plate under the taps system to stop pressure on the bath tub.
    Fit the flexible tap connectors to the bottom of the two taps utilizing 2 nuts as well as olives (often provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the outlet through the hole in the bath. Use the nut supplied by the producer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipe.
    Next off, fit completion of the versatile overflow pipeline to the overflow electrical outlet. After that, screw the pipe to the overflow face which ought to be fitted inside the bath. Ensure you utilize all of the supplied washers.
    Connect the trap to the bottom of the waste outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Attach all-time low of the overflow tube in a similar manner.The bath ought to now be ready to be suited its last placement.

    Tiling Around the Tub


    In the location where the bath meets the tile, it is required to seal the accompanies a silicone rubber caulking. This is very important as the installation can relocate sufficient to fracture a rigid seal, causing the water to penetrate the wall between the bath and also the tiling, leading to complications with moisture as well as feasible leakages to the ceiling listed below.
    You can pick from a variety of coloured sealants to blend in your fixtures as well as installations. They are offered in tubes and also cartridges, and also can securing gaps up to a width of 3mm (1/8 inch). If you have a larger gap to fill, you can fill it with twists of soaked newspaper or soft rope. Keep in mind to constantly fill up the tub with water prior to sealing, to allow for the movement experienced when the tub remains in usage. The sealer can split relatively early if you do not consider this movement before sealing.
    Conversely, ceramic coving or quadrant floor tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are likewise easily available on the marketplace. It is a good idea to fit the ceramic tiles utilizing water-resistant or water-proof glue as well as grout.

    A Step-by-Step Guide to Installing a Bathtub


    Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.



    But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.



    This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.


    Remove the Existing Bathtub


    To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.



    The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.


    Choose the Right Bathtub


    The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.


    Install the Plumbing and Ledger Board


    You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.



    Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.


    Install the Bathtub


    When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.



    Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.



    If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.


    Hook up the Plumbing


    Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.


    Install the Bathtub Surround


    A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.



    Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.



    If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.



    If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

    https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/


    How to Install a Bathtub

    I'm very curious about A Step-by-Step Guide to Installing a Bathtub and I am praying you enjoyed reading the page. If you liked our article plz make sure you remember to share it. Thanks for going through it.




    Schedule Now


    Report this page